Tag Archives: Steel Fisher

Steel Fisher v1.5 is coming

Posted on February 5, 2017 by janpenguin

I used Original Prusa i3 MK2 to print ABS parts. All printed ABS parts Replaced 12 balls Latest firmware: ReprapFirmware dc42 1.17d , DuetWebControl 1.14 Duet Web Control 1.14 It now monitors CPU temperature. During print the CPU temperature stayes … Continue reading →

Posted in DIY, Reprap 3D Printer | Tagged Duetwebcontrol, Reprap 3D Printer, RepRapFirmware, RepRapPro Fisher, Steel Fisher | Leave a comment

Power meter

Posted on November 15, 2016 by janpenguin

Parts: Single plug socket x1 Circuit breaker x1 Plug with three wires x1 Two wires, 30 cm Power meter x1 Wood piece x1 50 mm screw x6 20 mm Short screw x2 Zip-tie x2 (I used a AC 80-260V 100A … Continue reading →

Posted in DIY, Reprap 3D Printer | Tagged AC, power measurement, Reprap 3D Printer, Steel Fisher | Leave a comment

Extreme tests of Steel Fisher

Posted on November 9, 2016 by janpenguin

I’m preparining a 3D Farm business. So I’ve been printing difficult models that takes many hours with delicacy. 0.1 mm layer height, 33 hours, KISSlicer 0.1 mm layer height, 17 hours, KISSlicer Lea http://www.thingiverse.com/thing:620461 13 hours, KISSlicer 12 hours 49 … Continue reading →

Posted in Reprap 3D Printer | Tagged 3D model, cat, female body, KISSlicer, Reprap 3D Printer, Slic3r, slicer, Steel Fisher, voronoi | Leave a comment

Two Voronoi cats

Posted on October 23, 2016 by janpenguin

(10/28/2016) I used Meshmixer to add manual support. The Voronoi cat model took two hours and thirty minutes. Slic3r 1.2.9 to generate a gcode file without support. Filament: eSun PLA+ 1.75 mm Temperaure: 185 C Printing speed: 25 mm/s (Perimeters) … Continue reading →

Posted in Reprap 3D Printer | Tagged Fisher, Meshmixer, PLA, Reprap 3D Printer, retraction, Slic3r, Steel Fisher, support | Leave a comment

Steel Fisher – retraction calibration

Posted on October 19, 2016 by janpenguin

I was printing a big model that has heavy support. It had a lot of retraction and during the printing, the nozzle hit a piece, dislocated, then spewing filament in the air. Two hours and 46 minutes of work wasted. … Continue reading →

Posted in Reprap 3D Printer | Tagged B'struder, calibration, PLA, Reprap 3D Printer, retraction, Steel Fisher | Leave a comment

Built an Original Prusa i3 MK2.

Posted on October 12, 2016 by janpenguin

Now I have two RepRap 3D Printers. The left side is one day old Prusa i3 MK2, the right side is RepRapPro Fisher Beta, which I replaced most acrylic parts with steel and aluminum and named it Steel Fisher. After … Continue reading →

Posted in Reprap 3D Printer | Tagged assembly, Prusa i3 MK2, Reprap 3D Printer, Steel Fisher | 1 Comment

Book shelves

Posted on August 29, 2016 by janpenguin

(2016/10/15) I added 3D printed caps. The cap design file is here The 1st model was obscure. Later on I thought simply creating a cube with a cylinder would be sufficient. The right side of drawing was for the … Continue reading →

Posted in DIY | Tagged book shelf, DIY, OpenSCAD, Reprap 3D Printer, steel angle, Steel Fisher | Leave a comment