Bulbul Junior 3D Printer operation log – Day 5

http://www.thingiverse.com/thing:620461

Lea

cDSC_0046

cDSC_0048

cDSC_0050

cDSC_0053

Slic3r – gcode generator
Prontface – 3D Printer control

Print setting
; generated by Slic3r 1.1.7 on 2015-02-22 at 20:31:47
; perimeters extrusion width = 0.40mm
; infill extrusion width = 0.40mm
; solid infill extrusion width = 0.40mm
; top infill extrusion width = 0.40mm
; support material extrusion width = 0.40mm
G21 ; set units to millimeters
G28 ; home all axes
G29
M106
G1 X0 Y0 Z65 F5000 ; lift nozzle
M104 S210
M109 S205 ; wait for temperature to be reached
G90 ; use absolute coordinates
G92 E0
M82 ; use absolute distances for extrusion

; filament used = 12362.7mm (29.7cm3)
; avoid_crossing_perimeters = 0
; bed_size = 170,170
; bed_temperature = 0
; bridge_acceleration = 0
; bridge_fan_speed = 100
; bridge_flow_ratio = 1
; brim_width = 1
; complete_objects = 0
; cooling = 1
; default_acceleration = 0
; disable_fan_first_layers = -1
; duplicate_distance = 6
; end_gcode = M104 S0 ; turn off temperature\nM106\nG28 X0 ; home X axis\nM84 ; disable motors\n
; external_perimeters_first = 1
; extruder_clearance_height = 20
; extruder_clearance_radius = 20
; extruder_offset = 0x0
; extrusion_axis = E
; extrusion_multiplier = 1
; fan_always_on = 1
; fan_below_layer_time = 60
; filament_diameter = 1.75
; first_layer_acceleration = 0
; first_layer_bed_temperature = 0
; first_layer_extrusion_width = 200%
; first_layer_speed = 25
; first_layer_temperature = 210
; g0 = 0
; gcode_arcs = 0
; gcode_comments = 0
; gcode_flavor = reprap
; infill_acceleration = 0
; infill_first = 0
; layer_gcode =
; max_fan_speed = 100
; min_fan_speed = 60
; min_print_speed = 10
; min_skirt_length = 1
; notes =
; nozzle_diameter = 0.4
; only_retract_when_crossing_perimeters = 1
; ooze_prevention = 1
; output_filename_format = [input_filename_base].gcode
; perimeter_acceleration = 0
; post_process =
; print_center = 0,0
; resolution = 0
; retract_before_travel = 2
; retract_layer_change = 0
; retract_length = 1.5
; retract_length_toolchange = 0
; retract_lift = 0.2
; retract_restart_extra = 0
; retract_restart_extra_toolchange = 0
; retract_speed = 15
; skirt_distance = 5
; skirt_height = 1
; skirts = 3
; slowdown_below_layer_time = 30
; spiral_vase = 0
; standby_temperature_delta = -5
; start_gcode = G28 ; home all axes\nM106\nG1 Z5 F5000 ; lift nozzle\n
; temperature = 190
; threads = 2
; toolchange_gcode =
; travel_speed = 400
; use_firmware_retraction = 0
; use_relative_e_distances = 0
; vibration_limit = 0
; wipe = 0
; z_offset = 0
; dont_support_bridges = 1
; extrusion_width = 0.4
; first_layer_height = 0.3
; infill_only_where_needed = 0
; interface_shells = 0
; layer_height = 0.2
; raft_layers = 1
; seam_position = nearest
; support_material = 1
; support_material_angle = 5
; support_material_enforce_layers = 5
; support_material_extruder = 1
; support_material_extrusion_width = 0
; support_material_interface_extruder = 1
; support_material_interface_layers = 3
; support_material_interface_spacing = 0.4
; support_material_interface_speed = 100%
; support_material_pattern = pillars
; support_material_spacing = 2.5
; support_material_speed = 60
; support_material_threshold = 0
; bottom_solid_layers = 3
; bridge_speed = 25
; external_perimeter_speed = 70%
; extra_perimeters = 1
; fill_angle = 45
; fill_density = 5%
; fill_pattern = honeycomb
; gap_fill_speed = 20
; infill_every_layers = 1
; infill_extruder = 1
; infill_extrusion_width = 0
; infill_speed = 60
; overhangs = 1
; perimeter_extruder = 1
; perimeter_extrusion_width = 0
; perimeter_speed = 30
; perimeters = 3
; small_perimeter_speed = 30
; solid_fill_pattern = rectilinear
; solid_infill_below_area = 70
; solid_infill_every_layers = 0
; solid_infill_extrusion_width = 0
; solid_infill_speed = 60
; thin_walls = 1
; top_infill_extrusion_width = 0
; top_solid_infill_speed = 50
; top_solid_layers = 3

458648 lines
12362.74mm of filament used in this print
The print goes:
– from -60.12 mm to 58.81 mm in X and is 118.94 mm wide
– from -48.95 mm to 45.95 mm in Y and is 94.89 mm deep
– from 0.00 mm to 100.50 mm in Z and is 100.50 mm high
Estimated duration: 502 layers, 5:25:00
Print started at: 20:42:47
-0.000 -0.000 -0.000 -0.510 -0.650 -0.650 -0.650
0.780 0.780 -0.010 -0.480 -0.700 -0.600 -0.600
2.110 0.800 0.060 -0.430 -0.650 -0.660 -0.430
2.030 0.940 0.230 -0.270 -0.520 -0.600 -0.410
2.310 1.270 0.540 0.060 -0.260 -0.310 -0.190
1.700 1.700 1.000 0.530 0.200 0.140 0.140
1.650 1.650 1.650 1.190 0.900 0.900 0.900
Print ended at: 01:28:13 and took 4:45:26
Setting hotend temperature to 0.000000 degrees Celsius.
>>> m106
SENDING:M106

cDSC_0017

cDSC_0018 The right arm fell apart due to the poor support pillar.cDSC_0020

cDSC_0022

cDSC_0024

cDSC_0032

Flaws and imperfection

cDSC_0034

cDSC_0036

Infill density 5% caused crack.

cDSC_0038 cDSC_0040

Layer height is 0.2 mm, nozzle diameter is 0.4 mm. The fingers look rough.

Is this resolution limit of Bulbul Junior?

cDSC_0044

About janpenguin

Email: janpenguin [at] riseup [dot] net Every content on the blog is made by Free and Open Source Software in GNU/Linux.
This entry was posted in DIY, Reprap 3D Printer and tagged , , , . Bookmark the permalink.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s